Black shrink wrap is the name many warehouses, removal firms and distributors use for the opaque black film that goes round a pallet to hold it together and hide what is on it. In most cases the film they mean is black stretch film. It is pulled tight by hand and clings to itself, and it needs no heat. Pack Solution sells that film in three full width rolls and one narrow mini roll. We do not sell heat shrink film, heat guns or shrink tunnels, and this guide explains the difference so you can buy the right thing first time.
Below you will find what each black roll is for, how black compares with clear, how to get a wrap that nobody can see through, and the mistakes that waste film.
In This Guide
- Quick picks for black film
- What is black shrink wrap, and what do we actually sell?
- How does black stretch film differ from heat shrink film?
- Why choose opaque film over clear?
- Which black roll suits your job?
- How do you get a fully opaque wrap?
- What about small bundles and parcels?
- What mistakes waste black film?
- Who uses black pallet wrap?
- Ordering black film from Pack Solution
- Frequently Asked Questions
Quick picks for black film
If you already know you want opaque film, these three cover almost every job, from a full pallet to a bundle of boxes on a desk.
Best for hiding the contents of a full pallet
Black Pallet Wrap
Opaque hand stretch film that clings to itself, so the load stays tight and out of sight without tape or heat.
- 400mm x 120m, 20 micron, 750g
- 400mm x 200m, 20 micron, extended core
- 500mm x 250m, 23 micron, 1.8kg
From £4.00 ex VAT (£4.80 inc VAT)
Choose sizeView product
Best for small bundles you want kept private
Mini Handy Pallet Wrap 100mm x 150m
A narrow 17 micron roll in black or clear for bundling boxes, tubes and furniture parts.
- 100mm x 150m per roll
- 17 micron, clear or black
- Fits the HW38 dispenser
From £2.50 ex VAT (£3.00 inc VAT)
Choose sizeView product
Best for loads where labels must stay readable
Clear Pallet Wrap
Clear hand stretch film so barcodes and contents can be checked without unwrapping.
- 400mm and 500mm wide rolls
- 20 or 23 micron
- Standard or extended core
From £4.00 ex VAT (£4.80 inc VAT)
Choose sizeView productWhat is black shrink wrap, and what do we actually sell?
Two different films get called shrink wrap. Heat shrink film is laid loosely over or round a product and then heated, usually with a heat gun or a shrink tunnel, so it contracts tight against the shape. Stretch film is stretched as you wrap it, and its own tension and cling hold the load. On a pallet in a UK warehouse, the black wrap you see is nearly always the second kind.
Our Black Pallet Wrap is opaque hand stretch film. Each layer grips the one below, so the load stays tight without tape. There are three rolls:
- 400mm x 120m, 20 micron, standard core, 750g. A short, light roll for occasional wrapping, small loads and removals.
- 400mm x 200m, 20 micron, extended core, 1.4kg. More film, and a core you can grip without a dispenser.
- 500mm x 250m, 23 micron, standard core, 1.8kg. The widest, thickest and longest black roll.
So if a supplier list or a colleague asks for a black shrink wrap roll for pallets, any of these will do the job they have in mind. If you really need black shrink film for heat shrinking a product, such as sealing a single item with a heat gun, that is a different product and we do not stock it. Our guide to shrink wrap vs stretch wrap goes through the two films side by side.
No heat needed. Every black roll we sell is stretch film. You pull it tight round the load and it holds by cling, so you do not need a heat gun, a tunnel or any power supply.
How does black stretch film differ from heat shrink film?
The two films are made to behave differently, and that changes the kit, the time and the result.
| Black stretch film (what we sell) | Heat shrink film (we do not sell) | |
|---|---|---|
| How it holds | Stretched round the load, clings to itself | Wrapped loosely, then heated so it contracts |
| Kit needed | Your hands, or an extended core roll; a knife to cut | Heat gun or shrink tunnel, plus film |
| Typical use | Holding pallet loads and bundles together | Sealing individual products or shaped items |
| Removing it | Cut and peel off | Cut away |
| Our rolls | 400mm and 500mm black pallet wrap, 100mm black mini wrap | None |
For pallets, stretch film has practical advantages. You can wrap anywhere, including a loading bay or the back of a van, because there is nothing to plug in. You can start, stop and add a few more turns wherever the load feels loose. And because the film holds by cling, the load can be unwrapped quickly at the other end with a single cut.
Heat shrink has its place for retail packs and single items that need a tight, sealed skin. If that is your job, you need a specialist supplier. If the goal is to hold boxes on a pallet and keep them out of sight, black stretch film is the right product, and it is the one we stock.
Why choose opaque film over clear?
Black film is opaque, so once the pallet is wrapped nobody can see what is on it. That adds a little security. A pallet of phones, tools, branded stock or confidential paperwork looks the same as a pallet of anything else, which helps when it sits on a depot floor, in a shared yard or on an open trailer.
Some opaque shrink film products are sold for the same reason, to keep a product hidden. If the reason you were looking for opaque film was privacy rather than heat sealing, black stretch film gives you that without the heat gun.
There are good reasons to choose clear instead. Clear Pallet Wrap lets warehouse staff read labels and barcodes through the film, and lets a driver or goods-in team check the load without cutting it open. If your customer scans cartons on arrival, clear is usually the better choice. Clear comes in 400mm x 120m (20 micron), 400mm x 200m (23 micron), 400mm x 250m extended core (23 micron) and 500mm x 250m (23 micron).
A simple rule works for most businesses. Use black when the contents are valuable, confidential or easy to recognise. Use clear when someone at the other end needs to see or scan the cartons. Many warehouses keep both on the shelf.
Which black roll suits your job?
All three full width black rolls are the same film colour and all are made for wrapping by hand. The differences are width, length, thickness and core.
| Roll | Thickness | Core | Weight | Good for |
|---|---|---|---|---|
| 400mm x 120m | 20 micron | Standard | 750g | Occasional use, small loads, house moves |
| 400mm x 200m | 20 micron | Extended | 1.4kg | Regular hand wrapping without a dispenser |
| 500mm x 250m | 23 micron | Standard | 1.8kg | Full pallets, bigger loads, fewer roll changes |
| Mini 100mm x 150m | 17 micron | Mini roll | Not listed | Bundles, small boxes, furniture parts |
Width. A 500mm roll covers more of the pallet's height with each turn, so a tall load needs fewer passes. A 400mm roll is lighter in the hand and easier for smaller loads.
Thickness. The 500mm roll is 23 micron and the 400mm rolls are 20 micron. Micron is the thickness of the film. Thicker film gives a little more strength per layer. Our guide to pallet wrap grades and gauges explains micron and gauge in more detail.
Core. On the 400mm x 200m roll the cardboard core sticks out past the film at each end. You hold the ends and walk round the pallet, so you do not need a dispenser. That makes it the easiest black roll to use if you wrap by hand every day.
For a warehouse doing a handful of pallets a week, the 400mm x 200m extended core roll is a sensible default. For heavier or taller loads, the 500mm x 250m roll at 23 micron is the stronger choice. For a one-off house move, the 400mm x 120m roll is light and easy to carry.
How do you get a fully opaque wrap?
Black film hides the load well, but only if there are no gaps between the turns. These steps give a clean, fully covered pallet. For the full method, see our guide on how to wrap a pallet step by step.
- Stack the load square. Keep cartons inside the edge of the pallet, heaviest at the bottom. Overhanging boxes tear film and leave gaps.
- Tie the film to the pallet. Tuck the loose end between two cartons or twist it round a corner of the pallet, then wrap the base two or three times. The base turns lock the load to the pallet.
- Work upwards with an overlap. Walk round the load and raise the roll slowly, so each turn overlaps the last by roughly half the film width. With black film, that overlap is what stops light and eyes getting through.
- Keep tension even. Pull the film firmly enough that it stretches and clings. Slack film sags and leaves see-through thin spots.
- Finish at the top and come back down. Add two or three turns at the top, fold some film over the top edge if the load allows, then work back down to the base.
- Cut and press the tail. Cut the film with a knife and press the tail flat against the wrap so it clings.
- Label on the outside. Put the delivery label and any warnings on top of the black film. A label under black wrap cannot be read.
A sharp blade makes the last step much tidier. Our Utility Knives come in three models: the Pacplus MRK metal retractable knife, the Pacplus CPK18 18mm knife and the Kinetix MDC18 18mm snap-off knife, which lets you snap to a fresh edge when the blade goes dull. Retract or cover the blade after every cut.
Best for cutting film cleanly at the end of a wrap
Utility Knives
Three models for cutting stretch film, tape and cardboard on the bench or the warehouse floor.
- Pacplus MRK metal retractable
- Pacplus CPK18 18mm
- Kinetix MDC18 18mm snap-off
From £1.90 ex VAT (£2.28 inc VAT)
Choose sizeView productWhat about small bundles and parcels?
A full width roll is too big for bundling a few boxes or keeping a drawer shut. For those jobs, Mini Handy Pallet Wrap 100mm x 150m comes in black or clear. Each roll is 17 micron and 150m long. Black hides the contents, which is useful for stock in transit or furniture parts. Clear lets you see the items and read labels.
Load it into the HW38 Handy Wrap Dispenser and the roll spins as you walk it round the bundle, so the film goes on more evenly and your hands stay off it. The HW38 takes mini handy rolls only. It is too small for full width pallet rolls.
Best for faster, neater mini roll wrapping
HW38 Handy Wrap Dispenser
A hand-held holder for mini handy rolls, so the roll spins and your hands stay off the film.
- Takes mini handy stretch wrap rolls
- Sold per piece
- Rolls sold separately
£2.50 ex VAT (£3.00 inc VAT)
Buy nowView productTypical small jobs for black mini wrap include holding two or three cartons together, wrapping lengths of pipe or cable, keeping doors and drawers closed on small furniture, and covering a parcel so the box print is hidden. Our guide to handy wrap and mini pallet wrap covers these jobs in more detail.
What mistakes waste black film?
Most problems with black pallet wrap come from how it goes on, not from the film itself.
- Too little overlap. Gaps between turns let people see the cartons underneath, which defeats the point of opaque film. Overlap each turn by about half.
- Too much film. Endless turns in one spot waste film and make the wrap harder to remove. Add layers where the load needs them, usually the base and the top.
- Skipping the base. If the film does not lock the bottom cartons to the pallet, the whole stack can slide as one block. Always start with turns round the base.
- Sharp corners. Unprotected corners on cartons or metal goods can tear the film. Stack neatly and keep edges inside the pallet.
- Labels under the wrap. Delivery labels go on top of black film. Under it, nobody can scan them.
- Expecting heat shrink results. Stretch film will not shrink to a product's shape when heated. If you need a sealed skin round a single item, you need heat shrink film from a specialist supplier.
If you send heavy pallets, add a Caution Heavy label to the outside of the wrap. Our warning labels come as Caution Heavy 148 x 50mm (500 per roll) and Fragile 89 x 32mm (1000 per roll). For quick repairs to a torn wrap or bundling odd items, black duct tape in 48mm x 50m blends in on black film.
Who uses black pallet wrap?
Our product page lists the uses we see most: high value or confidential stock, holding pallet loads together for storage and transport, discreet storage and house removals, and bundling cartons together. In practice that covers a wide range of businesses.
Warehouses and distributors wrap outbound pallets of stock they would rather not advertise. Removal firms wrap furniture and boxes going into storage. Online sellers wrap a pallet of returns or bulk stock before it goes to a fulfilment centre. Offices moving sites wrap archive boxes so the contents stay private on the way.
For storage and removals, the 400mm x 120m roll is often enough. For regular outbound pallets, the 400mm x 200m extended core roll or the 500mm x 250m roll will save time and roll changes.
Ordering black film from Pack Solution
Every roll is sold on its own, with a minimum order of one, and the price per roll falls as you buy more. Prices on the site are shown ex VAT, and every order comes with a VAT invoice. Royal Mail Tracked 48 is free on every order with no minimum, and orders placed by 2pm Monday to Friday are dispatched the same working day. Faster paid options are at checkout.
If you are within 10 miles of our unit in Cheetham Hill, our vans can bring orders placed by 12pm Monday to Friday the same day; see our local delivery page. Free click and collect from Unit 2, 50 Derby Street, Manchester M8 8HF is usually ready within 2 hours. Businesses that order regularly can apply for a trade account.
The full range of black and clear rolls is in the pallet wrap collection. Knives and dispensers are in the equipment collection, and packing tape is in the tapes collection. If you run a stretch wrap machine and want to check film before ordering, call 0161 706 1246 or email sales@packsolution.co.uk.
Need black film today? Order by 2pm Monday to Friday for same-day dispatch with free Tracked 48, or collect from Cheetham Hill, usually within 2 hours.
Frequently Asked Questions
Is black pallet wrap the same as black shrink wrap?
They are often treated as the same thing, but the film works differently. Our black pallet wrap is hand stretch film. You pull it tight round the load and it clings to itself, with no heat gun. True heat shrink film is wrapped loosely and then heated so it contracts. We do not sell heat shrink film.
What thickness is your black stretch film?
The two 400mm rolls are 20 micron and the 500mm x 250m roll is 23 micron. The black mini handy wrap is 17 micron.
Can you see through black pallet wrap?
The film is opaque, so the load is hidden from view once it is wrapped. Use enough overlapping layers that no gaps are left between turns, and keep the delivery label on the outside of the wrap.
Do I need a dispenser for black pallet wrap?
No. All our full width rolls are made for wrapping by hand. The 400mm x 200m black roll has an extended core that sticks out past the film, so you can hold it without a dispenser. The HW38 dispenser is for mini handy rolls only.
Can I buy a single roll?
Yes. Every roll is sold on its own with a minimum order of one, and the price per roll drops as you buy more. Royal Mail Tracked 48 is free on every order.
Will black film work on my wrapping machine?
Our rolls are hand stretch film. If you run a stretch wrap machine, call 0161 706 1246 before you order so we can talk through what you need.

